Відео

Thank you for the info. Maybe you could answer me some questions? Does the oilpressure sensor itself leak or does it come loose? On my mothers car we had to put a wrench on it and bolt that to the block because it would come loose all the time. And since we are from germany the only parts available for the cruiser is cheap chinese crap. We had to this after the fith sensor we bought came loose again. And now there are these two codes. I can always delete them but they come back after a couple of days. Are there wishbones and engine mounts that last longer then two years in the us? If so from which manufacturer? Anyways thank you again. This helps a lot.

Saved the job. Thank you!!!

OMG amazing video. This has just saved me. Thank you.

Thank you! I installed a short shifter and when I was adjusting the centering cable, the green tab popped out! Now I can't find it, so I guess I'll be replacing the whole cable now 😂

What if u can't get in the car like in my problem

Maybe put a round punch through the bolt hole and break it that way??

Sooo simple 😂

For some reason people think oil drains faster when the oil is warm/hot. Multi-viscosity oil works the opposite of this thinking. Thinner when cold; thickens as it gets hot.

How much do I owe you? Because I didn't have to go to the dealership, thats $80 just to show up. (I did use a heavy towel between the pry bar and the hood just to make sure I didn't scratch my mother in laws paint)

Thank you my dude.

THANK YOU! So many other videos took 10 mins saying try this try that, yours was straight to the point and got the hood of my car opened

I do all our familes vehicles, but I own a 2021 Harley Davidson tri glide and don have the experiece to service it. I received a recall to have a sensor replace and to do a full inspection as my cycle has 1,200 miles on it. I took it to the place I bought from as it was a better deal deal then my old Harley Dealer. The invoice showed sensor replace and was charged $100 for total inspection. A week later sensor ligh came on, so I rode it up to my older dealer and found sensor never done and the brake fuid should have been flushed and refilled and wasn't touched. Older dealer went ahead and did allthe service over and only charged be $100 for everything. I wrote Harley headquarters and emailed the 1st and 2nd receipt. Harley Davidson Home office did nothing!! This tells me the manufacturer doesn't care either!!! Only my older dealer corrected the problem!!

Mine gets stuck to the seal from the heat outside.

That plastic clip is more a dirt shield than a device to hold the lever. The lever is fine on its own.

Just Subscribed for This video Appreciation 👍

Today 6-27-24, I want to fill the CVT transmission fluid..... But look and see Several plugs make me Confused which is which. So I Stopped and Towed to the Shop..... before f.up

Just did my 2018 Outback front and rear diffs. Rear piece of cake. Front was a bitch mainly due to fill plug removal. At least 150+lbs of torque to break it loose and then when it did I lost half the skin on my left thumb. Should have worn gloves! I’m not a small guy 6’1” 200lbs and work out regularly … it took all I had.

I see little oil inside my distributor cap edges. Will this affect my idle very low and about to die out my car when stop?

Thanks good video

Thank you so much for this video and I appreciate your absolute candor ( Star Trek ). It’s nice to find somebody that is very specific and they show you and tell you because so many people nowadays don’t show you they just tell you I really really appreciate you and your time because I would much rather do it myself then pay SUBARU a lot of money that I don’t have because I haven’t been working because of Cancer , so thank you thank you again 😊

I'm trying this immediately

Thank you very much for your video! It is very helpful!

Thanks boss chuckled to myself when I realized I just need to get off my cheeks and drain dat hoe and fill er up.

Have this car in the shop RN replaced both b1 b2 the next day code came back on. tomorrow gonna check that first thing. Never thought about even looking at a tsb.

You should stop giving out free advice when you dont understand how the crush gasket works

Very good sounding prius

You’re a damn genius! This worked right away after I struggled for an hour!

You don't put exhaust piping over the piece you are attaching to, you need it smaller than the piece you are atgachjng to. This is so the gases dont encounter an edge and leak.

also happened to me, but i had to drill that out cuz it was stuck as hell

Lift with positive and negative 😮. You be a light bulb

Love peace and chicken grease.

Thank you 🙏🏾

Imagine that

Good thank you

Hey I had the same issue and I cleaned my sensor with maf cleaner and used contact cleaner on the conector and started her up and she ran fine then the revs start dropping and it start making a lot more shit sounds out the exhaust as if it’s misfiring more then what it was before hand. Any more suggestions?

Thank you so much… This worked while I was stuck in a shopping center and had to get to an appointment!!!!

Oil looks like pancake mix

👍 Thank you so much, you trick worked for me. You avoid me to call for a car mechanic because merover my battery was dead.

One of the best if not the best impacts on the marker right now

Worked perfect. Conciseness is appreciated!

A Prius I didn’t know toasters had catalytic converters

Yeah thank you I don't do EVS but this is really good knowledge thank you😎✌🐧 Kim in N.W. Commiefornia

Thank you 🎉

The cable looks lose 😮

Not too bad of a diy repair. For 241k miles, that is a solid little car. What's the price for an OEM pump?

What about the line on the bell of pulley?

Ty. Been battling those two codes on my pt cruiser

Thank you so much! 😊 for being generous to share your knowledge to us.. 👍 God bless

I saw the same amount of slop in both sockets. So I’ll stick with my 30 year old craftsman sockets.

Someone using a javelin in the background